Forschung
Publikationen

Veröffentlichungen des Sonderforschungsbereichs

Internationale wissenschaftliche Beiträge in Fachzeitschriften, begutachtet

  • Kellersmann A.; Reitz, G.; Friedrichs, J. (2018) Sensitivity analysis of blisk airfoil wear International Journal of Turbomachinery, Propulsion and Power 2018, 3(2), 14
    DOI: 10.3390/ijtpp3020014
  • Kellersmann A.; Reitz, G.; Friedrichs, J. (2018) Deterioration effects of coupled blisk bladesJournal of the Global Power and Propulsion Society. 2: 465–476.
    DOI: 10.22261/JGPPS.CKB8N6
  • L.; Tatzko, S.; Panning-von Scheidt, L.; Wallaschek, J. (2018) High order sensitivity analysis of a mistuned blisk including intentional mistuning Journal of Theoretical and Applied Mechanics 55 (1), 353-368
    DOI: 10.15632/jtam-pl.55.1.353
  • Langen, D.; Maier, H. J.; Hassel, T. (2018) The Effect of SiC Addition on Microstructure and Mechanical Properties of Gas Tungsten Arc-WeldedTi-6Al-4V AlloyJournal of Materials Engineering and Performance 2018 (27) (1), 253--230
    DOI: 10.1007/s11665-017-3091-y
  • Rogge T.; Berger, R.; Pohle, L.; Rolfes, R.; Wallaschek, J. (2018) Efficient structural analysis of gas turbine bladesAircraft Eng & Aerospace Tech (Aircraft Engineering and Aerospace Technology) 90 (9), S. 1305–1316
    DOI: 10.1108/AEAT-05-2016-0085
  • Böß, V.; Rust, F.; Denkena, B.; Dittrich, M.-A. (2017) Design of individual re-contouring processesProcedia Manufacturing 14, 76-88
    DOI: 10.1016/j.promfg.2017.11.009
  • Denkena, B.; Grove, T.; Mücke, A.; Langen, D.; Nespor, D.; Hassel, T. (2017) Residual stress formation after re-contouring of micro-plasma welded Ti-6Al-4 V parts by means of ball end millingMaterials Science and Engineering Technology 2017, 1034-1039
    DOI: 10.1002/mawe.201600743
  • Gilge, P.; Hohenstein, S.; Seume, J. R. (2017) Experimental Investigation of the Aerodynamic Effect of Local Surface Roughness on a Turbine BladeInternational Journal of Gas Turbine, Propulsion and Power System
  • Hauptmann, T.; Aschenbruck, J.; Seume, J. R. (2017) Forced Response Excitation due to Stagger Angle Variation in a Multi-Stage Axial TurbineInternational Journal of Gas Turbine, Propulsion and Power Systems Volume 9 (Number 3), 1--11
  • Kaierle, S.; Overmeyer, L.; Alfred, I.; Rottwinkel, B.; Hermsdorf, J.; Wesling, V.; Weidlich, N. (2017) Single-crystal turbine blade repair by laser cladding and remeltingCIRP Journal of Manufacturing Science and Technology 2017 (19), 196--199
    DOI: 10.1016/j.cirpj.2017.04.001
  • Li, Y.; Kästner, M.; Reithmeier, E. (2017) Vibration-insensitive Low Coherence Interferometer (LCI) for the Measurement of Technical SurfacesMeasurement
    DOI: 10.1016/j.measurement.2017.03.010
  • Matthias, S.; Schlobohm, J.; Kästner, M.; Reithmeier, E. (2017) Fringe projection profilometry using rigid and flexible endoscopestm - Technisches Messen 84 (2)
    DOI: 10.1515/teme-2016-0054
  • Nicolaus, M.; Möhwald, K.; Maier, H. J. (2017) A Combined Brazing and Aluminizing Process for Repairing Turbine Blades by Thermal Spraying Using the Coating System NiCrSi/NiCoCrAlY/AlJ Therm Spray Tech 9 (1), S. 13
    DOI: 10.1007/s11666-017-0612-z
  • Nicolaus, M.; Rottwinkel, B.; Alfred, I.; Möhwald, K.; Nölke, C.; Kaierle, S.; Maier, H.J.; Wesling, V. (2017) Future regeneration processes for high-pressure turbine bladesCEAS Aeronautical Journal 2017 (online)
    DOI: 10.1007/s13272-017-0277-9
  • Rottwinkel, B.; Kaierle, S.; Wesling, V. (2017) Laser cladding for cracked CMSX-4 single-crystalline turbine partsLasers in Manufacturing and Materials Processing 4 (1), 13-23
    DOI: 10.1007/s40516-016-0033-8
  • Berger, R.; Rogge, T.; Jansen, E.; Rolfes, R. (2016) Probabilistic vibration and lifetime analysis of regenerated turbomachinery bladesAdvances in Aircraft and Spacecraft Science 3 (4), S. 503–521
    DOI: 10.12989/aas.2016.3.4.503
  • Böß, V.; Denkena, B.; Wesling, V.; Kaierle, S.; Rust, F.; Nespor, D.; Rottwinkel, B. (2016) Repairing parts from nickel base material alloy by laser cladding and ball end millingIn: Prod. Eng. Res. Devel. 10 (4-5), S. 433–441
    DOI: 10.1007/s11740-016-0690-7
  • Bruchwald, O.; Frackowiak, W.; Reimche, W.; Maier, H. J. (2016) Applications of High Frequency Eddy Current Technology for Material Characterization of Thin CoatingsIn: Journal of Materials Science and Engineering 2016 (6), S. 185–191
    DOI: 10.17265/2161-6213/2016.7-8.001
  • Gilge P.; Mulleners, K. (2016) Resulting Aerodynamic Losses of Combinations of Localized Roughness Patches on Turbine BladesAIAA Journal 54 (8), S. 2552–2555
    DOI: 10.2514/1.J054602
  • Hartmann U.; Seume, J. R. (2016) Combining ART and FBP for improved fidelity of tomographic BOSMeas. Sci. Technol. 27 (9), S. 097001
    DOI: 10.1088/0957-0233/27/9/097001
  • Hartmann, U.; Hennecke, C.; Dinkelacker, F.; Seume, J. R. (2016) Automatic Detection of Defects in a Swirl Burner Array Through an Exhaust Jet Pattern AnalysisIn: J. Eng. Gas Turbines Power 139 (3)
    DOI: 10.1115/1.4034449
  • Hohl A.; Wallaschek, J. (2016) A Method to Reduce the Energy Localization in Mistuned Bladed Disks by Application-Specific Blade Pattern ArrangementJ. Eng. Gas Turbines Power 138 (9), S. 092502
    DOI: 10.1115/1.4032739
  • Kellenbrink, C.; Helber, S. (2016) Quality- and profit-oriented scheduling of resource-constrained projects with flexible project structure via a genetic algorithmIn: European Journal of Industrial Engineering Volume 10, 2016
    DOI: DOI: 10.1504/EJIE.2016.078807
  • Kuprat, T.; Nyhuis, P. (2016) Designing Capacity Synchronization within the Regeneration of Complex Capital GoodsIn: Universal Journal of Management 2016 (4(10)), S. 581
    DOI: 10.13189/ujm.2016.041008
  • Nespor D.; Denkena, B.; Grove, T.; Pape, O. (2016) Surface topography after re-contouring of welded Ti-6Al-4V parts by means of 5-axis ball nose end millingInt. J. Adv. Manuf. Technol. 85 (5-8), S. 1585–1602
    DOI: 10.1007/s00170-015-7885-5
  • Pösch A.; Schlobohm, J.; Matthias, S.; Reithmeier, E. (2016) Rigid and flexible endoscopes for three dimensional measurement of inside machine parts using fringe projectionOptics and Lasers in Engineering 2016
    DOI: 10.1016/j.optlaseng.2016.05.023
  • Schlobohm J.; Bruchwald, O.; Frackowiak, W.; Li, Y.; Kästner, M.; Pösch, A.; Reimche, W.; Reithmeier, E.; Maier, H. J. (2016) Turbine blade wear and damage – An overview of advanced characterization techniquesMaterials Testing 58 (5), S. 389–394
    DOI: 10.3139/120.110872
  • Schlobohm J.; Pösch, A.; Reithmeier, E.; Rosenhahn, B. (2016) Improving contour based pose estimation for fast 3D measurement of free form objectsMeasurement 92 (92), S. 79–82
    DOI: 10.1016/j.measurement.2016.05.093
  • Schlobohm, J.; Li, Y.; Pösch, A.; Kästner, M.; Reithmeier, E. (2016) Multiscale measurement of air foils with data fusion of three optical inspection systemsIn: CIRP Journal of Manufacturing Science and Technology 2016
    DOI: 10.1016/j.cirpj.2016.07.006
  • Schlobohm, J.; Pösch, A.; Reithmeier, E. (2016) A Raspberry Pi Based Portable Endoscopic 3D Measurement SystemIn: Electronics 5 (3), S. 43
    DOI: 10.3390/electronics5030043
  • Zou, Y.; Li, Y.; Kästner, M.; Reithmeier, E. (2016) Low-coherence interferometry based roughness measurement on turbine blade surfaces using wavelet analysisIn: Optics and Lasers in Engineering 82, S. 113–121
    DOI: 10.1016/j.optlaseng.2016.02.011
  • Aschenbruck, J.; Seume, J. R. (2015) Experimentally Verified Study of Regeneration-Induced Forced Response in Axial TurbinesJournal of Turbomachinery 137 (3), S. 1–10
    DOI: 10.1115/1.4028350
  • Bonhage, M.; Pohle, L.; Panning-von Scheidt, L.; Wallaschek, J. (2015) Transient Amplitude Amplification of Mistuned Blisks BonhageJ. Eng. Gas Turbines Power 137 (11), S. 1125-02
    DOI: 10.1115/1.4030278
  • Denkena, B.; Boess, V.; Nespor, D.; Floeter, F.; Rust, F. (2015) Engine blade regeneration: a literature review on common technologies in terms of machiningInt J Adv Manuf Technol 81 (5-8), S. 917–924
    DOI: 10.1007/s00170-015-7256-2
  • Flöter, F.; Denkena, B. (2015) Analysis of Chatter Vibration and Tool Deflection in Milling with a Novel Active Machine Tool GuideIn: Applied Mechanics and Materials 794, S. 331–338
    DOI: 10.4028/www.scientific.net/AMM.794.331
  • Kellenbrink, C.; Helber, S. (2015) Scheduling resource-constrained projects with a flexible project structure KellenbrinkEuropean Journal of Operational Research 246 (2), S. 379–391
    DOI: 10.1016/j.ejor.2015.05.003
  • Li, Y.; Kästner, M.; Reithmeier, E. (2015) High-precision surface measurement with an automated multiangle low coherence interferometerApplied Optics 54 (6), S. 1232
    DOI: 10.1364/AO.54.001232
  • Nespor, D.; Denkena, B.; Grove, T.; Böß, V. (2015) Differences and similarities between the induced residual stresses after ball end milling and orthogonal cutting of Ti–6Al–4VJournal of Materials Processing Technology 226, S. 15–24
    DOI: 10.1016/j.jmatprotec.2015.06.033
  • Nicolaus, M.; Möhwald, K.; Maier, H. J. (2015) Combined brazing and alitising process for thermally sprayed Ni-based alloys for the repair of turbine bladesThermal Spray Bulletin 2015 (8) (2), S. 56–61
  • Adamczuk, R.R.; Luehrmann, J.; Seume, J.R. (2014) Methodology for evaluating hot gas path defects in an exhaust jetAerospace Science and Technology 39 (Vol. 39), S. 120–127
    DOI: 10.1016/j.ast.2014.08.011
  • Denkena, B.; Gümmer, O.; Flöter, F. (2014) Evaluation of electromagnetic guides in machine toolsCirp Annals 63, S. 357–360
    DOI: 10.1016/j.cirp.2014.03.130
  • Denkena, B.; Nespor, D.; Böß, V.; Köhler, J. (2014) Residual stresses formation after re-contouring of welded Ti-6Al-4V parts by means of 5-axis ball nose end millingCIRP Journal of Manufacturing Science and Technology 7 (4), S. 347–360
    DOI: 10.1016/j.cirpj.2014.07.001
  • Eickemeyer, S. C.; Herde, F.; Irudayaraj, P.; Nyhuis, P. (2014) Decision models for capacity planning in a regeneration environmentInternational Journal of Production Research 52 (23), S. 7007–7026
    DOI: 10.1080/00207543.2014.923122
  • Holl, M.; Rogge, T.; Loehnert, S.; Wriggers, P.; Rolfes, R. (2014) 3D multiscale crack propagation using the XFEM applied to a gas turbine bladeComput Mech 53 (1), S. 173–188
    DOI: 10.1007/s00466-013-0900-5
  • Loehnert, S. (2014) A stabilization technique for the regularization of nearly singular extended finite elementsComput Mech 54 (2), S. 523–533
    DOI: 10.1007/s00466-014-1003-7
  • Mulleners, K.; Gilge, P.; Hohenstein, S. (2014) Impact of Surface Roughness on the Turbulent Wake Flow of a Turbine BladeJournal of Aerodynamics 2014, S. 1–9
    DOI: 10.1155/2014/458757
  • Böß, V.; Nespor, D.; Samp, A.; Denkena, B. (2013) Numerical simulation of process forces during re-contouring of welded parts considering different material propertiesCIRP Journal of Manufacturing Science and Technology 6 (3), S. 167–174
    DOI: 10.1016/j.cirpj.2013.05.001
  • Denkena, B.; Flöter, F. (2013) Adaptive Cutting Force Control with a Hybrid Axis SystemInternational Journal of Automation Technology 7 (4), S. 379–384
  • Eickemeyer, S. C.; Borcherding, T.; Schäfer, S.; Nyhuis, P. (2013) Validation of data fusion as a method for forecasting the regeneration workload for complex capital goodsProd. Eng. Res. Devel. 7 (2-3), S. 131–139
    DOI: 10.1007/s11740-013-0444-8
  • Holl, M.; Loehnert, S.; Wriggers, P. (2013) An adaptive multiscale method for crack propagation and crack coalescenceInt. J. Numer. Meth. Engng 93 (1), S. 23–51
    DOI: 10.1002/nme.4373
  • Nicolaus, M.; Möhwald, K.; Bach, F.-W.; Maier, H. J. (2013) Heat treatment of thermal sprayed Ni-base-fillermetal-NiCrAlY-coating systems for repairing turbine bladesThermal Spray Bulletin 2013 (6) (2), S. 119–123
  • Adamczuk, R.; Seume, J. R. (2012) Time Resolved Full-Annulus Computations of a Turbine with Inhomogeneous Inlet ConditionsInternational Journal of Gas Turbine, Propulsion and Power Systems 4,2, S. 01–07

Internationale wissenschaftliche Beiträge in Fachzeitschriften, nicht begutachtet

  • Nicolaus, M.; Möhwald, K.; Bach, F.-W.; Maier, H. J. (2014) Heat Treatment of thermally sprayed Ni-based brazing materials NiCrAlY coating systems for the repair of turbine bladesWelding and Cutting 2014 (2), S. 108–111
  • Pösch, A.; Kästner, M.; Reithmeier, E. (2014) Fringe projection measurement of highly specular objects in presence of multi-reflectionComputational vision and medical image processing IV. London: 2014 Taylor & Francis Group, London, S. 127–131
  • Pösch, A.; Vynnyk, T.; Reithmeier, E. (2013) Fast Detection of Geometric Defects on Free-Form Surfaces Using Inverse Fringe ProjectionThe Journal of the CMSC 2013, S. 10–14

Internationale Konferenzbeiträge, begutachtet

  • Hennecke, C.; Haar, H. von der; Dinkelacker, F. (2019) Numerical Simulation of Gas Turbine Burning Chamber Combustion with Defined Burner DefectsProceedings of the Global Power & Propulsion Forum (GPPF) 2019.
  • Denkena, B.; Mücke, A.; Schumacher, T.; Langen, D.; Hassel, T. (2018) Technology-based Re-contouring of Blade Integrated Disks After Weld RepairJ. of Materi Eng and Perform 27, 2018 (1), 253-260
    DOI: 10.1115/1.4040738
  • Denkena, B; Mücke, A.; Schumacher, T.; Langen, D.; Grove, T.; Bergmann, B.; Hassel, T. (2018) Ball end milling of titanium TIG weld material and the effect of SiC addition – process forces and shape deviations6th International Conference on Through-life Engineering Services, TESConf 2017. 7-8 November 2017, Bremen, Germany, Seite 74-81
    DOI: 10.1016/j.promfg.2018.01.011
  • Frackowiak, W.; Barton, S.; Reimche, W.; Bruchwald, O.; Zaremba, D.; Schlobohm, J.; Li, Y., Kaestner, M.; Reithmeier, E. (2018) Near-Wing Multi-Sensor Diagnostics of Jet Engine ComponentsASME Turbo Expo 2018: Turbomachinery Technical Conference and Exposition; Oslo, Norway, June 11–15, 2018
    DOI: 10.1115/GT2018-76793
  • Hartmann, U.; Seume, J. (2018) Automated Condition Evaluation of Hot-Gas Path Components of Jet Engines through Exhaust Jet Analysis Proceedings of the ASME Turbo Expo 2018, 11-15 June 2018, Oslo, Norway, GT2018-75384
  • Hartung, K.; Gilge, P.; Herbst, F. (2018) Towards Immersed Boundary Methods for Complex Roughness Structures in Scale-Resolving Simulations32nd European Conference on Modelling and Simulation (ECMS 2018), 22-25 May 2018, Wilhelmshaven, Germany
    ISBN: 78-0-9932440-6-3
  • Hauptmann, T.; Meinzer, C. E.; Seume, J. R. (2018) Experimental Validation of Forced Response Methods in a Multi-Stage Axial TurbineProceedings of the ASME Turbo Expo 2018, 11-15 June 2018, Oslo, Norway, GT2018-75390
  • Hauptmann, T.; Seume, J. R. (2018) Blade Vibration Measurements in a Multi-Stage Axial Turbine with Geometric Variations2018 AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, AIAA SciTech Forum, 8-12 January 2018, Kissimmee, Florida, USA, AIAA 2018-0952
    DOI: 10.2514/6.2018-0952
  • Kellersmann, A.; Reitz, G.; Friedrichs, J. (2018) Deterioration effects of coupled blisk bladesGlobal Power and Propulsion Forum, Proceedings of Montreal 2018
  • Salomon, J.; Kruse, S.; Broggi, M.; Weber, S.; Beer, M. (2018) Decision-Making for Resilience-Enhancing Endowments in Complex Systems using Principles of Risk MeasuresProc. of the 6th Intl. Symposium on Reliability Engineering and RiskManagement (6ISRERM)Resilience and Sustainability of Urban Systems.
    DOI: 10.3850/978-981-11-2726-7_CRR06
  • Schnabel A.; Kellenbrink, C.; Helber, S. (2018) Profit-oriented scheduling of resource-constrained projects with flexible capacity constraintsBusiness Research TBA
    DOI: 10.1007/s40685-018-0063-5
  • Schnabel, A.; Kellenbrink, C. (2018) Scheduling resource-constrained projects with makespan-dependent revenues and costly overcapacity Proceedings of the 16th International Conference on Project Management and Scheduling, Rome (Italy), pp. 205-208
  • Wolff, J.; Kolditz, T.; Fei, Y.; Raatz, A. (2018) Simulation-Based Determination of Disassembly Forces7th CIRP Conference on Assembly Technologies and Systems (CATS 2018). Procedia CIRP 76 (2018), 13 – 18
    DOI: 10.1016/j.procir.2018.01.022
  • Hoffmann, L.-S.; Kuprat, T.; Kellenbrink, C.; Schmidt, M.; Nyhuis, P. (2017) Priority based planning approaches for regeneration processesProcedia CIRP 2017 (59), 89-94
  • Keller, C.; Kellersmann, A.; Friedrichs, J.; Seume, J. R. (2017) Influence of Geometric Imperfections on Aerodynamic and Aeroelastic Behavior of a Compressor BliskIn: Proceedings of ASME Turbo Expo 2017, Charlotte, USA, GT2017-63556
  • Kellersmann, A.; Reitz, G.; Friedrichs, J. (2017) Sensitivity analysis of blisk airfoil wearISROMAC 2017 - 17th International Symposium on Transport Phenomena and Dynamics of Rotating Machinery, Maui, USA, Dec 16-21.
  • Miro, S.; Broggi, M.; Beer, M.; Willeke, T., Seume, J.R. (2017) Survival signature approach for the reliability analysis of an axial compressor.In: Cepin, M. et al. (eds.) Safety and Reliability – Theory and Application: ESREL 2017, Proceedings of the European Safety and Reliability Conference (ESREL 2017), Taylor & Francis Group, London.
  • Schlobohm, J.; Bruchwald, O.; Frąckowiak, W.; Li, Y.; Kästner, M.; Pösch, Reimche, W.; Maier, H. J., Reithmeier, E. (2017) Advanced Characterization Techniques for Turbine Blade Wear and DamageProcedia CIRP Bd. 59: ELSEVIER, S. 83–88
  • Schwerdt, L.; Berger, R.; Keller, C.; Seume, J.; Rolfes, R.; Panning-von Scheidt, L.; Wallaschek, J. (2017) Influence of Blade Repairs on Compressor Blisk Vibration considering Aerodynamic Damping and MistuningGPPS (Hg.): Proceedings of Global Power and Propulsion Society Conference. Shanghai
  • Willeke, S.; Keller, C.; Panning-von Scheidt, L.; Seume, J.; Wallaschek, J. (2017) Reduced Order Modeling of Mistuned Bladed Disks Considering Aerodynamic Coupling and Mode Family InteractionIn: Proceedings of 12th European Conference on Turbomachinery Fluid Dynamics & Thermodynamics (ETC12), April 3-7, Stockholm, Sweden, ETC2017-242
  • Adamczuk, R.; Seume, J. R. (2016) Numerical Evaluation of the Condition of a Jet Engine through Exhaust Jet AnalysisIn: ASME (Hg.): Proceedings of the ASME Turbo Expo 2016
  • Böß, V.; Grove, T.; Denkena, B.; Mücke, A.; Nespor, D. (2016) Prediction of the Principal Stress Direction for 5-axis Ball End MillingProcedia CIRP 45, S. 291–294
    DOI: 10.1016/j.procir.2016.02.145
  • Hartmann, U.; Hennecke, C.; Dinkelacker, F.; Seume, J. R. (2016) Automatic Detection of Defects in an Annular Swirl Burner Array Through an Exhaust Jet Pattern AnalysisProceedings of the ASME Turbo Expo 2016, S. 1–10
  • Hauptmann, T.; Seume J.R. (2016) Aerodynamic Excitation for Variable Tip GapIn: Proceedings of ASME Turbo Expo 2016: Turbomachinery Technical Conference & Exposition
  • Hurfar, C. Mandanna; Keller, C.; Mumcu, A.; Seume, J. R. (2016) An Acoustic Excitation System for the Generation of Turbomachinery Specific Sound Fields: Part II - Experimental VerificationIn: Proceedings of the ASME Turbo Expo 2016, Seoul, South Korea
  • Kuprat, T.; Schmidt, M.; Nyhuis, P. (2016) Model-based analysis of reassembly processes within the regeneration of complex capital goodsIn: Procedia CIRP 2016 (55), S. 206
  • Mumcu, A.; Keller, C.; Hurfar, C. Mandanna; Seume, J. R. (2016) An Acoustic Excitation System for the Generation of Turbomachinery Specific Sound Fields: Part I - Design and MethodologyIn: Proceedings of the ASME Turbo Expo 2016, Seoul, South Korea
  • Nicolaus, M.; Möhwald, K.; Maier, H. Jürgen (2016) Regeneration of high pressure turbine blades. Development of a hybrid brazing and aluminizing process by means of thermal sprayingIn: Proceida CIRP. The 5th International Conference on Through-life Engineering Services (TESConf 2016): Elsevier B.V, S. 5.
  • Schwerdt, L.; Hauptmann, T.; Kunin, A.; Wallaschek, J.; Wriggers, P.; Panning-von Scheidt, L. et al. (2016) Aerodynamical and Strucutral Analysis of Operationally used Turbine BladesIn: 5th International Conference on Through-life Engineering Services, Cranfield, England
  • von der Haar, Henrik; Hartmann, U.; Hennecke, C.; Dinkelacker, F.; Seume, J. R. (2016) Early Defect Detection on an annular Swirl-Burner-Array by Optical Measuring Exhaust Gases and Numerical AnalysisIn: Proceedings of the ASME Turbo Expo 2016, June 13-17, 2016, Seoul, South Korea
  • Aschenbruck, J.; Hauptmann, T.; Seume, J. R. (2015) Influence of a Multi-Hole Pressure Probe on the Flow Field in Axial-TurbinesEuropean Turbomachinery Conference ETC11. Madrid
  • Denkena, B.; Böß, V.; Nespor, D.; Gilge, P.; Hohenstein, S.; Seume, J. (2015) Prediction of the 3D Surface Topography after Ball End Milling and its Influence on AerodynamicsProcedia CIRP 31, S. 221–227
    DOI: 10.1016/j.procir.2015.03.049
  • Denkena, B.; Böß, V.; Nespor, D.; Rust, F. (2015) Simulation and Evaluation of Different Process Strategies in a 5-axis Re-contouring ProcessProcedia CIRP 35, S. 31–37
    DOI: 10.1016/j.procir.2015.08.059
  • Hartmann, U.; Seume, J. R. (2015) Application of an Algebraic Reconstruction Algorithm to Tomographic BOS MeasurementsIn: Gas Turbine Society of Japan (Hg.): Proceedings of International Gas Turbine Congress 2015, Japan, S. 1214–1221
  • Hauptmann, T.; Aschenbruck, J.; Seume, J. R. (2015) Forced Response Excitation due to Variances in a Multi-Stage Axial TurbineProceedings of International Gas Turbine Congress 2015, Tokyo, Japan
  • Hohenstein, S.; Gilge, P.; Seume, J. R. (2015) Experimental Investigation of the Aerodynamic Effect of Local Surface Roughness on a Turbine BladeIn: Gas Turbine Society of Japan (Hg.): Proceedings of the International Gas, S. 371–380.
  • Keller, C.; Willeke, T.; Burrafato, S.; Seume, J. R. (2015) Design Process of a 1.5-Stage Axial Compressor for Experimental Flutter InvestigationsIn: Proceedings of the International Gas Turbine Congress 2015, Tokyo, Japan, S. 1130–1139
  • Li, Y.; Kästner, M.; Reithmeier, E. (2015) Development of a compact low coherence interferometer based on GPGPU for fast microscopic surface measurement on turbine bladesSPIE Optical Metrology 2015, Proc. SPIE 9525, Optical Measurement Systems for Industrial Inspection IX, 95250R (pp. 95250R-95250R), Munich
    DOI: 10.1117/12.2184749
  • Weingaertner, W.; Schweitzer, L.; Rottwinkel, B.; Noelke, C.; Kaierle, S.; Wesling, V. (2015) Single-Crystal (SX) Laser Cladding of CMSX48th Brazilian Congress of Manufacturing Engineering (COBEF). Brazilian Society of Engineering and Mechanical Sciences. Salvador / Brazil, 22.05.2015
  • Aschenbruck, J.; Adamczuk, R.; Seume, J. R. (2014) Recent Progress in Turbine Blade and Compressor Blisk Regeneration3rd International Conference on Through-life Engineering Services; Session: Recent Progress in Jet-Engine Regeneration, Bd. 22. Cranfield, England, S. 256–262
    DOI: 10.1016/j.procir.2014.07.016
  • Aschenbruck, J.; Seume, J. R. (2014) Experimentally Verified Study of Regeneration-Induced Forced Response in Axial TurbinesProceedings of the ASME Turbo Expo 2014, S. GT2014-25664
  • Denkena, B.; Böß, V.; Nespor, D.; Rust, F.; Flöter, F. (2014) Approaches for Improving Cutting Processes and Machine Tools in Re-contouringProcedia CIRP 22, S. 239–242
    DOI: 10.1016/j.procir.2014.06.148
  • Denkena, B.; Dahlmann, D.; Flöter, F.; Brühne, T. (2014) Conceptual Design for Electromagnetic Guided Rotary Table in Machine ToolsProcedia CIRP 24, S. 80–85
    DOI: 10.1016/j.procir.2014.08.010
  • Eickemeyer, S. C.; Steinkamp, S.; Schuster, B.; Schäfer, S. (2014) From Fuzzy Maintenance, Repair and Overhaul Data to Reliable Capacity PlanningNew Production Technologies in Aerospace Industry Proceedings of the 4th Machining Innovations Conference, Hannover, September 2013: Springer International Publishing Switzerland 2014, S. 181–186
    DOI: 10.1007/978-3-319-01964-2_24
  • Kellenbrink, C. (2014) First Results on Quality-Oriented Scheduling of Flexible ProjectsProceedings of the 14th International Conference on Project Management and Scheduling, S. 129–132
  • Kellenbrink, C. (2014) First results on resource-constrained project scheduling with model-endogenous decision on the project structureOperations research proceedings 2012, Selected papers of the International Annual Conference of the German Operations Research Society (GOR), Leibniz Universität Hannover, Germany, September 5-7, 2012. Cham: Springer, S. 429–434
  • Kellenbrink, C.; Herde, F.; Eickemeyer, S. C.; Kuprat, T.; Nyhuis, P. (2014) Planning the Regeneration Processes of Complex Capital GoodsProcedia CIRP 24, S. 140–145
    DOI: 10.1016/j.procir.2014.08.001
  • Kellersmann, A.; Reitz, G.; Friedrichs, J. (2014) Numerical investigation of circumferential coupled deterioration effects of a jet engine compressor front stage compared to BLISK geometryProceedings of the 3rd International Conference in Through-life Engineering Services 2014 (22), S. 249–255
    DOI: 10.1016/j.procir.2014.07.006
  • Pohle, L.; Panning-von Scheidt, L.; Wallaschek, J.; Aschenbruck, J.; Seume, J. R. (2014) Dynamic Behavior of a Mistuned Air Turbine: Comparison Between Simulations and MeasurementsProceedings of ASME Turbo Expo 2014: Turbine Technical Conference and Exposition. Düsseldorf, Germany, S. V07BT33A015
    DOI: 10.1115/GT2014-26025
  • Rottwinkel, B.; Nölke, C.; Kaierle, S.; Wesling, V. (2014) Crack Repair of Single Crystal Turbine Blades Using Laser Cladding TechnologyProcedia CIRP 22, S. 263–267
    DOI: 10.1016/j.procir.2014.06.151
  • Rottwinkel, B.; Schweitzer, L.; Nölke, C.; Kaierle, S.; Wesling, V. (2014) Challenges for Single-Crystal (SX) Crack CladdingPhysics Procedia 56, S. 301–308
    DOI: 10.1016/j.phpro.2014.08.175
  • Schlobohm, J.; Li, Y.; Pösch, A.; Langmann, B.; Kästner, M.; Reithmeier, E. (2014) Multiscale Optical Inspection Systems for the Regeneration of Complex Capital GoodsProcedia CIRPProceedings of the 3rd International Conference in Through-life Engineering Services, Bd. 22: ELSEVIER, S. 243–248
    DOI: 10.1016/j.procir.2014.07.019
  • Schlobohm, J.; Li, Y.; Pösch, A.; Langmann, B.; Kästner, M.; Reithmeier, E. (2014) Multiscale Optical Inspection Systems for the Regeneration of Complex Capital GoodsProcedia CIRP. Proceedings of the 3rd International Conference in Through-life Engineering Services, Bd. 22: ELSEVIER, S. 243–248
  • Adamczuk, R.; Buske, C.; Roehle, I.; Hennecke, C.; Dinkelacker, F.; Seume, J. R. (2013) Impact of Defects and Damage in Aircraft Engines on the Exhaust JetProceedings of the ASME Turbo Expo, 3-7 June 2013, San Antonio, USA, GT2013-95709
  • Adamczuk, R.; Hartmann, U.; Seume, J. R. (2013) Experimental Demonstration of Analyzing an Engine's Exhaust Jet with the Background-Oriented Schlieren MethodAIAA Ground Testing Conference, 24-27 June 2013, San Diego, USA
  • Adamczuk, R.; Seume, J. R. (2013) Early Assessment of Defects and Damage in Jet EnginesInternational Through-Life Engineering Services Conference, Bd. 11. Cranfield, England, S. 328–333
    DOI: 10.1016/j.procir.2013.07.022
  • Aschenbruck, J.; Meinzer, C.; Pohle, L.; Panning-von Scheidt, L.; Seume, J. R. (2013) Regeneration-Induced Forced Response in Axial TurbinesASME Turbo Expo 2013Turbine Technical Conference and Exposition, June 3-7, 2013, San Antonio, Texas, USA. San Antonio, Texas, USA, S. V07BT33A010
    DOI: 10.1115/GT2013-95431
  • Aschenbruck, J.; Meinzer, C.; Seume, J. R. (2013) Influence of Regeneration-Induced Variances of Stator Vanes on the Vibration Behavior of Rotor Blades in Axial Turbines10th European Conference on Turbomachinery. Lappeenranta, Finland, S. 235–247
  • Hohenstein, S.; Aschenbruck, J.; Seume, J. R. (2013) Aerodynamic Effects of Non-Uniform Surface Roughness on a Turbine BladeProceedings of ASME Turbo Expo. ASME. San Antonio, 01.01.2013
  • Hohenstein, S.; Seume, J. R. (2013) Numerical Investigation on the Influence of Anisotropic Surface Roughness on the Skin FrictionProceedings of 10th European Conference on Turbomachinery (ETC), 15-19 April 2013. Lappeenranta University of Technlogy. Lappeenranta, Finnland, 01.01.2013
  • Böß, V. (2012) Milling Simulation of Welded Aero Engine ComponentsProceedings of the 3rd Machining Innovations Conference, S. 403–410
  • Denkena, B.; Flöter, F. (2012) Adaptive Cutting Force Control on a Milling Machine with Hybrid Axis ConfigurationProcedia CIRP 4, S. 109–114
    DOI: 10.1016/j.procir.2012.10.020
  • Adamczuk, R.; Seume, J. R. (2011) Time Resolved Full-Annulus Computations of a Turbine with Inhomogeneous Inlet ConditionsInternational Gas Turbine Congress 2011 Osaka, Japan, IGTC2011-0175
  • Denkena, B.; Böß, V.; Nespor, D.; Samp, A. (2011) Kinematic and Stochastic Surface Topography of Machined TiAl6V4-Parts by Means of Ball Nose End Milling1st CIRP Conference on Surface Integrity (CSI), Bd. 19, S. 81–87
    DOI: 10.1016/j.proeng.2011.11.083
  • Hohl, A.; Kriegesmann, B.; Wallaschek, J.; Panning-von Scheidt, L. (2011) The Influence of Blade Properties on the Forced Response of Mistuned Bladed DisksASME 2011 Turbo Expo: Turbine Technical Conference and Exposition, S. 1159–1170
    DOI: 10.1115/GT2011-46826
  • Denkena, B.; Hackelöer, F. (2010) Multi-sensor Disturbance Force Measurement for Compliant Mechanical Structures9th Annual IEEE Conference on Sensors, S. 2518–2524
    DOI: 10.1109/ICSENS.2010.5690446
  • Eickemeyer, S. C.; Nyhuis, P. (2010) Capacity Planning and Coordination with Fuzzy Load InformationThe Business Review, Cambridge 16 (1), S. 259–264

Internationale Konferenzbeiträge, nicht begutachtet

  • Bittner, S. L.; Keller, C.; Meinzer, C. E.; Seume, J. R. (2018) Experimental Validation of a Forced Response Analysis Using a Time-Linearized Method2018 AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, AIAA SciTech Forum
    DOI: 10.2514/6.2018-0461
  • Gilge, P.; Seume, J.; Mulleners, K. (2018) Analysis of local roughness combinations on the aerodynamic properties of a compressor blade2018 AIAA Aerospace Sciences Meeting, AIAA SciTech Forum, 8-12 January 2018, Kissimmee, Florida, USA, AIAA2018-0345
  • Hartmann, U.; Haar, H. von der; Dinkelacker, F.; Seume, J. (2018) Experimental Defect Detection in a Swirl-Burner Array Through Exhaust Jet Analysis2018 AIAA Aerospace Sciences Meeting, AIAA SciTech Forum, 8-12 January 2018, Kissimmee, Florida, USA, AIAA2018-0303
    DOI: 10.2514/6.2018-0303
  • Hoffmann, L.-S.; Kellenbrink, C. (2018) Scheduling Multiple Flexible Projects with Different Variants of Genetic Algorithms Proceedings of the 16th International Conference on Project Management and Scheduling, Rome (Italy), pp. 128-131
  • Kurth, S.; Hamann, C.; Seume, J.; Mulleners, K. (2018) Experimental Investigation of the Influence of Anisotropic Surface Structures on the Boundary Layer FlowInstitute of Aeronautics and Astronautics (Hg.): 2018 AIAA SciTech Forum Aerospace Sciences Meeting, Kissimmee, Florida, USA
  • Haar, H. von der; Hennecke, C.;. Dinkelacker, F. (2017) Approach of Future Defect Detection in Aircraft Engines by Optical Measuring Exhaust GasesCombustion Institute (Hg.): Proceedings of the 8th European Combustion Meeting
  • Kunin, A.; Loehnert, S.; Wriggers, P. (2017) Thermo-mechanical modeling of turbine blades taking into account structural defects88th Annual Meeting of the International Association of Applied Mathematics and Mechanics. Weimar, 2017
  • Nicolaus, M.; Möhwald, K.; Maier, H. J. (2017) Heat treatment of the thermally sprayed coating system NiCrSi/NiCoCrAlY/Al for repair brazing high pressure turbine bladesIn: ITSC 2017. DVS-Berichte, Band: 336. DVS Media GmbH, Düsseldorf, 2017, S. 462-466
  • Bruchwald, O.; Frackowiak, W.; Reimche, W.; Maier, H. Jürgen (2016) Applications of high frequency eddy current technology for material characterization of thin coatingsProceedings 12th International Conference The "A" Coatings 2016, S. 37–43, Garbsen: PZH Verlag
  • Bruchwald, O.; Nicolaus, M.; Frackowiak, W.; Möhwald, K.; Reimche, W.; Maier, H. Jürgen (2016) Material Characterization of Thin Coatings Using High Frequency Eddy Current Technology.World Conference on Non-Destructive Testing; WCNDT. München.
  • Ernst, B.; Seume, J. R.; Herbst, F. (2016) Probabilistic CFD-Analysis of Regeneration-Induced Geometry Variances in a Low-Pressure TurbineIn: 52nd AIAA/SAE/ASEE Joint Propulsion Conference, Propulsion and Energy Forum, Salt Lake City, Utah, USA, S. AIAA 2016--4555.
  • Frackowiak, W.; Bruchwald, O.; Reimche, W.; Maier, H. Jürgen (2016) Applications of high frequency induction thermography in the megahertz range for material characterization of turbine componentsProceedings 12th International Conference The "A" Coatings 2016, S. 31–36, Garbsen: PZH Verlag
  • Frackowiak, W.; Bruchwald, O.; Zwoch, S.; Reimche, W.; Maier, H. Jürgen (2016) Non-Destructive Damage Detection and Material Characterization of Turbine Components Using Megahertz Range Induction Thermography in Pulsed ModeIn: 19th Proceedings of World Conference on Non-Destructive Testing; WCNDT. Munich, Germany
  • Kaierle, S.; Rottwinkel, B. (2016) Development of new laser technologies for repairing single crystal turbine bladesInt. Laser- und Fügesymposium. Fraunhofer-Institut für Werkstoff- und Strahltechnik IWS. Dresden, 01.01.2016
  • Kunin, A.; Loehnert, S.; Wriggers, P. (2016) Thermo-mechanical contact between crack surfaces in the eXtended Finite Element MethodECCOMAS 2016: European Congress on Computational Methods in Applied Sciences and Engineering. Crete Island
  • Kunin, A.; Loehnert, S.; Wriggers, P. (2016) Thermo-mechanical contact between crack surfaces in the eXtended Finite Element MethodCMIS 2016: Contact Mechanics International Symposium. Warsaw, Poland
  • Li, Y.; Bossmeyer, H.; Kästner, M.; Reithmeier, E. (2016) Development of an edge sensor based on polyview optics and laser triangulation principleIn: International Society for Optics and Photonics (Hg.): SPIE/COS Photonics Asia (inproceedings) S. 100231
  • Flöter, F.; Pohle, L.; Denkena, B.; Panning-von Scheidt, L.; Wallaschek, J. (2015) Mistuning of Blisks During Milling Process - Manufacturing and RepairIn: Deutsche Gesellschaft für Luft- und Raumfahrt (Hg.): Deutscher Luft- und Raumfahrtkongress (DLRK)
  • Gilge, P.; Mulleners, K. (2015) On the resulting aerodynamic loss of combinations of localized surface roughness patches on a turbine bladeIn: American Institute of Aeronautics and Astronautics (Hg.): 33rd AIAA Applied Aerodynamics Conference Dallas
  • Hamann, C.; Kurth, S.; Mulleners, K. (2015) Towards Quantifying Effects of Refractive Index Mismatch on PIV ResultsProceedings of 11th International Symposium on Particle Image Velocimetry - PIV15, 14-16 September 2015, Santa Barbara, USA
  • Hartmann, U.; Adamczuk, R.; Seume, J. R. (2015) Tomographic Background Oriented Schlieren Applications for Turbomachinery 53rd AIAA Aerospace Sciences Meeting (invited), 5-9 January 2015, Kissimmee, Florida
    DOI: 10.2514/6.2015-1690
  • Hauptmann, T.; Aschenbruck, J.; Christ, P.; Hennecke, C.; Dinkelacker, F.; Seume, J. R. (2015) Influence of Combustion Chamber Defects on the Forced Response Behavior of Turbine Blades. Proceedings of the 14th International Symposium on Unsteady Aerodynamics, Aeroacoustics & Aeroelasticity of Turbomachines, ISUAAAT14, 8-11 September 2015, Stockholm, Schweden, S. 9
  • Kunin, A.; Loehnert, S.; Wriggers, P. (2015) A multiscale projection method for the thermomechanical simulation of the interaction of microcracks with a macrocrackX-DMS 2015, eXtended Discretization Methods, Ferrara, Italy, September 9-11, 2015
  • Li, Y.; Kästner, M.; Reithmeier, E. (2015) Compact Optical Sensor for the Measurement of Surface Microtopographies on Turbine BladesAMA Conference 2015, Proceedings SENSOR 2015, Nürnberg, Germany
    DOI: 10.5162/sensor2015/C6.3
  • Nicolaus, M.; Möhwald, K.; Maier, H. J. (2015) Development of a two-stage hybrid technology for repairing turbine bladesProceedings from the International Thermal Spray Conference and Exposition 2015. ASM International, Materials Park, Ohio, S. 37–40
  • Nicolaus, M.; Rottwinkel, B.; Möhwald, K.; Nölke, C.; Kaierle, S.; Maier, H. J.; Wesling, V. (2015) Future regeneration processes for high pressure turbine blades64. Deutscher Luft- und Raumfahrtkongress 2015, 22-24 September 2015. Deutsche Gesellschaft für Luft- und Raumfahrt - Lilienthal-Oberth e.V.®. Rostock, 24.09.2015
  • Schlobohm, J.; Pösch, A.; Reithmeier, E. (2015) A rigid borescopic fringe projection system for 3D measurement for hard to access areas and limited space - ViboscopCMSC 2015. Coordinate Metrology Society. Miami, FL, USA, 21.08.2015.
  • Adamczuk, R.; Hartmann, U.; Seume, J. R. (2014) Application of the Background-Oriented Schlieren Method for the Analysis of an Engine's Exhaust JetXXII Biannual Symposium on Measuring Techniques in Turbomachinery, 4-5 September 2014, Lyon, France
  • Loehnert, S.; Holl, M.; Prange, C. (2014) 3D error controlled adaptive XFEM simulation of ductile fracture on multiple scalesWCCM. IACM. Barcelona, 01.01.2014
  • Nicolaus, M.; Möhwald, K.; Maier, H. J. (2014) Common application of Ni-based fillermetals and hotgascorrosion protection coatings by means of thermal spraying with subsequent heat treatment for near net shape turbineblade repairingProceedings / 11th International Conference THE "A" Coatings in Manufacturing Engineering, 1 - 3 October 2014, Thessaloniki, Greece. Thessaloniki: Ed. Ziti, S. 179–184
  • Reithmeier, E.; Matthias, S.; Schlobohm, J.; Ohrt, C.; Pösch, A. (2014) Endoskopische 3D-MesstechnikDGaO Proceedings 2014 (5)
  • Schlobohm, J.; Pösch, A.; Kästner, M.; Reithmeier, E. (2014) On the development of a low-cost rigid borescopic fringe projection systemFront Matter: Volume 9450: SPIE digital library
    DOI: 10.1117/12.2067310
  • Frackowiak, W.; Bruchwald, O.; Reimche, W.; Bach, F.-W.; Maier, H. J. (2013) High Frequency Eddy-Current and Induction Thermography Inspection Techniques18th International Workshop on Electromagnetic Non-Destructive Evaluation. Bratislava, SK, 24.06.2013
  • Hennecke, C.; Frieling, D.; Dinkelacker, F. (2013) Influence of Combustion Chamber Disturbances to Patterns in the Hot Gas PathEuropean Combustion Meeting 2013
  • Holl, M.; Loehnert, S.; Wriggers, P. (2013) An adaptive multiscale method for three-dimensional crack propagation in elasto-plastic mediaXFEM conference. Lyon, 01.01.2013
  • Holl, M.; Loehnert, S.; Wriggers, P.; Nicolaus, M. (2013) Three-dimensional crack propagation in ductile media using the XFEMCFRAC. Prag, 01.01.2013
  • Krauss, M.; Kästner, M.; Reithmeier, E. (2013) Data quality estimation from interdependencies for structural light scannersTavares, João Manuel R. S. und Jorge, R. M. Natal (Hg.): Computational vision and medical image processing IV, S. 191–195
  • Rottwinkel, B.; Nölke, C.; Hustedt, M.; Kaierle, S.; Wesling, V. (2013) Single Crystal Crack Cladding of CMSX-424th Advanced Aerospace Materials and Processes (AeroMat) Conference and Exposition. American Society for Metals. Bellevue / USA, 03.05.2013
  • Holl, M.; Loehnert, S.; Wriggers, P. (2012) A fully adaptive multiscale framework for three dimensional crack propagation using the XFEMWCCM. Sao Paulo, 01.01.2012
  • Holl, M.; Loehnert, S.; Wriggers, P. (2012) A multiscale framework for 3D crack propagation using the XFEMECCOMAS. Wien, 01.01.2012
  • Krauss, M.; Kästner, M.; Reithmeier, E. (2012) Multi-Scale Inspection of Worn Surfaces for Product RegenerationMSC 2012, New Orleans: Spring 2013, S. 28–32
  • Nicolaus, M.; Möhwald, K.; Bach, F.-W. (2012) A New Hybrid Process for Repair Brazing and Coating of Turbine BladesThermal Spray 2012: Proceedings from the International Thermal Spray Conference and Exposition. Ohio: ASM International, S. 110–113
  • Pohle, L.; Panning-von Scheidt, L.; Wallaschek, J. (2012) Reduced Order Model of Mistuned Bladed Disks Using the Krylov-Subspace Combined with the Craig-Bamton Reduction TechniqueIn Proceedings of the 10th World Congress on Computational Mechanics: Blucher Mechanical Engineering Proceedings, S. 899–908
    DOI: 10.5151/meceng-wccm2012-18187
  • Pösch, A.; Vynnyk, T.; Reithmeier, E. (2012) Using Inverse Fringe Projection to Speed Up the Detection of Local and Global Geometry Defects on Free Form SurfacesProceedings of SPIE, Vol. 8500
    DOI: 10.1117/12.928700
    ISBN: 9780819492173
  • Rottwinkel, B.; Nölke, C.; Hustedt, M.; Kaierle, S.; Wesling, V.; Weidlich, N. (2012) Single Crystal (SX) Laser Cladding of CMSX-4Icaleo 2012. LIA - Laser Institute of America. Anaheim / USA, 28.09.2012
  • Adamczuk, R.; Aschenbruck, J.; Bartelt, M.; Herbst, F.; Seume, J. R. (2011) Inverse Methods in Turbomachinery ApplicationsAachen Conference on Computational Engineering Science (ACCES). Aachen, 01.01.2011
  • Holl, M.; Loehnert, S.; Wriggers, P. (2011) Crack coalescence in a multiscale frameworkCFRAC. Barcelona, 01.01.2011
  • Holl, M.; Loehnert, S.; Wriggers, P. (2011) Crack propagation and crack coalescence in a multiscale frameworkUSNCCM. USACM. Minneapolis, 01.01.2011
  • Nicolaus, M.; Möhwald, K.; Bach, F.-W. (2011) Repair Brazing of Turbine Blades using Thermal SprayingProceedings. Thessaloniki: Ed. Ziti, S. 347–352
  • Pösch, A.; Vynnyk, T.; Kästner, M.; Abu-Namous, O.; Reithmeier, E. (2010) Virtual Inverse Fringe ProjectionCMSC 2010. CMSC. Reno, Nevada, USA, 01.01.2010

Nationale wissenschaftliche Beiträge in Fachzeitschriften, begutachtet

  • Denkena, B.; Flöter, F.; Nespor, D.; Wesling, V.; Kaierle, S.; Hustedt, M.; Rottwinkel, B. (2013) Bauteilregeneration bei einkristalliner GefügestrukturWerkstattstechnik online 103 (6), S. 476–480
  • Möhring, H.-C.; Flöter, F.; Denkena, B. (2012) Messtechnische Analyse formflexibler Spannmethodenwt Werkstattstechnik online 102 (11), S. 795–800

Nationale wissenschaftliche Beiträge in Fachzeitschriften, nicht begutachtet

  • Denkena, B., Grove, T., Pape, O., Mücke, A. (2018) Prozessauslegung für die Regeneration komplexer InvestitionsgüterUnter Span, Ausgabe 2018, S. 22-23
  • Lucht T.; Schäfers, P.; Nyhuis, P. (2018) Durchgängige modellbasierte Bewertung von RegenerationslieferkettenZWF - Zeitschrift für wirtschaftlichen Fabrikbetrieb 113 (4), S. 220–224
    DOI: 10.3139/104.111893
  • Kuprat, T.; Burmeister, T.; Nyhuis, P. (2017) Bewertung von Gestaltungsoptionen in der RegenerationZWF - Zeitschrift für wirtschaftlichen Fabrikbetrieb 2017 (112) (6), 396-400
  • Kellenbrink, C.; Helber, S. (2016) Controlling in SonderforschungsbereichenForschung: Politik, Strategie, Management 9. Jahrgang (Heft 2, 2016) (2), 45-53
  • Kuprat, T.; Schmidt, M.; Nyhuis, P. (2016) Gestaltung von Regenerationslieferketten - Bewertung der Synchronität mithilfe des BereitsstellungsdiagrammesIn: ZWF - Zeitschrift für wirtschaftlichen Fabrikbetrieb 2016 (12), 809-812
  • Rust, F. (2016) Werkzeugwege für den individuellen ReparaturfallIn: phi 2016, S. 3.
  • Kuprat, T.; Nyhuis, P. (2015) Konfiguration von regenerationsspezifischen GestaltungsoptionenZeitschrift für den wirtschaftlichen Fabrikbetrieb 2015 (5) (110), S. 277–280
  • Eickemeyer, S. C.; Kruse, S.; Hübner, M.; Schäfer, S. (2013) Mathematische Modelle zur bedarfsgerechten KapazitätsplanungZWF 108 (07-08/2013), S. 552–555
  • Hohenstein, S.; Aschenbruck, J.; Seume, J. R. (2013) Einfluss betriebs- und regenerationsbedingter Varianzen von TurbinenschaufelnInternational Journal for Electricity and Heat Generation VGB PowerTech 2013 (11), S. 51–58
  • Eickemeyer, S. C.; Busch, J.; Heinke, Y.; Goßmann, D. (2012) Verfügbarkeitsoptimierung in der KapazitätsplanungZWF 107 (12), S. 903–907
  • Eickemeyer, S. C.; Goßmann, D.; Wesebaum, S.; Nyhuis, P. (2012) Entwicklung einer Schadensbibliothek für die Regeneration komplexer InvestitionsgüterIndustrie Management 28 (2), S. 58–61
  • Eickemeyer, S. C.; Herde, F. (2012) Regeneration komplexer Investitionsgüter - Potenziale für Kapazitätsplanung und -steuerung sowie AuftragsannahmeZeitschrift für wirtschaftlichen Fabrikbetrieb 2012 (10), S. 761–765
  • Reimche, W.; Frackowiak, W.; Bruchwald, O.; Böhm, V.; Bach, F.-W. (2012) Nachweis von lokalen Schädigungen an Hochleistungsbauteilen mit Hochfrequenz Wirbelstromtechniken und Induktions-ThermografieDACH-Jahrestagung 2012 Zerstörungsfreie Materialprüfung. Berlin: DGZfP
  • Denkena, B.; Köhler, J.; Grove, T.; Nespor, D. (2011) Den Exoten auf der Spur: Anwendungsgerechte Zerspanung von LeichtbauwerkstoffenWB Werkstatt + Betrieb 2011 (9), S. 60–64
  • Eickemeyer, S. C.; Doroudian, S.; Schäfer, S.; Nyhuis, P. (2011) Ein generisches Prozessmodell für die Regeneration komplexer InvestitionsgüterZWF 106 (11), S. 861–865
  • Krauss, M.; Ohrt, C.; Kästner, M.; Reithmeier, E. (2011) 3D Messtechnik für Inspektion und In-Situ ÜberwachungIngenieurspiegel, S. 71–72
  • Eickemeyer, S. C.; Krüger, C.; Nyhuis, P. (2010) Kapazitätsplanung und -abstimmung bei unscharfen BelastungsinformationenZWF 105 (4), S. 323–327
  • Samp, A. (2010) Forschen am IFW: Nach allen Regeln der Zerspankunstphi - Produktionstechnik Hannover informiert, 11 (2010) 2, S. 16-17

Nationale Konferenzbeiträge, begutachtet

  • Frackowiak, W.; Barton, S.; Bruchwald, O.; Reimche, W.; Zaremba, D. (2018) Entwicklung einer Hochfrequenz-Induktionsthermografie und -Wirbelstromtechnik zur Fehlerprüfung und Charakterisierung der Schichtsysteme von Triebwerksbeschaufelung im SchaufelkanalDGZfP-Jahrestagung 2018; 7. bis 9. Mai, Leipzig.
  • Helber, S.; Herde, F.; Hille, R. (2012) Regeneration ziviler FlugzeugtriebwerkeInternationales Verkehrswesen 64 (2), S. 65–68

Nationale Konferenzbeiträge, nicht begutachtet

  • Berger, R.; Rogge, T.; Rolfes, R. (2016) Fast Methods for Structural Analysis of Gas Turbine Blades with Manufacturing ImperfectionsDeutscher Luft- und Raumfahrtkongress, Braunschweig 13. - 15. September 2016
  • Hassel, T.; Langen, D.; Maier, H. J. (2016) Gefüge und Mechanische Eigenschaften impfbehandelter Schweißnähte an TitanIn: DVS Berichte Band 327, Große Schweißteschnische Tagung Leipzig. Düsseldorf, 49-53
  • Hennecke, C.; Hartmann, U.; von der Haar, Henrik; Dinkelacker, F.; Seume, J. R. (2015) Fehlerfrüherkennung von Brennkammerdefekten einer Ringbrennkammer aus einem 8-Drallbrenner-Array mittels optischer Abgasstrahlanalyse und numerischer Zuordnung27. Deutscher Flammentag Verbrennung und Feuerung, Düsseldorf: VDI-Verlag, S. 393–402
  • Hennecke, C.; Hartmann, U.; von der Haar, Henrik; Dinkelacker, F.; Seume, J. R. (2015) Correlation of Defects in an Annular Swirl-Burner-Array by Optical Measuring Exhaust Gases and Numerical Analysis64. Deutscher Luft- und Raumfahrtkongress 2015, 22-24 September 2015, Rostock
  • Kellersmann, A.; Gilge, P.; Seume, J.; Friedrichs, J. (2015) Performance impact of high pressure compressor blisk roughness.DLRK 2015. DGLR. Rostock, 01.01.2015.
  • Langen, D.; Swider, M. Alan; Hassel, T. (2015) Lichtbogenschweißen von Titanlegierungen - Einfluss von Impfmitteln auf das Schweißgefüge von TiAl6V4Tagungsband 1. Niedersächsisches Symposium Materialtechnik12. bis 13. Februar 2015. 1. Aufl. Herzogenrath: Shaker (Fortschrittsberichte der Materialforschung und Werkstofftechnik / Bulletin of Materials Research and Engineering, 1), S. 176–185
  • Aschenbruck, J.; Meinzer, C.; Seume, J. R. (2014) Regenerationsbedingte Nachlauferregung in AxialturbinenInstationäre Aerodynamik und Aeroelastik in Turbomaschinen. Institut für Energietechnik, Ruhr-Universität Bochum. Bochum, 05.03.2014
  • Denkena, B.; Flöter, F. (2014) Potentiale elektromagnetischer Linearführungen in WerkzeugmaschinenZWF 109, S. 625–628
  • Frackowiak, W.; Bruchwald, O.; Reimche, W.; Maier, H. J. (2014) Schicht-und Bauteilfehlerprüfung mit HF-Wirbelstromprüftechnik und HF-Induktionsthermografie390. Sitzung des Arbeitskreises Niedersachen. Deutsche Gesellschaft für Zerstörungsfreie Prüfung. Garbsen, 30.01.2014
  • Hennecke, C.; Maronna, T.; Dinkelacker, F. (2013) Detektion von Triebwerksbrennkammerfehlern durch Analyse von Temperatur- und Speziesprofilen der Heißgase einer Modell-BrennkammerDeutscher Flammentag 2013
  • Hohenstein, S.; Gilge, P.; Raulf, C.; Seume, J. R. (2013) Einfluss lokaler Rauheiten auf die aerodynamischen Verluste von TurbinenschaufelnDeutscher Luft- und Raumfahrtkongress 2013, 10-12 September. Stuttgart
  • Krauss, M.; Frackowiak, W.; Pösch, A.; Kästner, M.; Reithmeier, E.; Maier, H. J. (2013) Assessment of used turbine blades on and beneath the surface for product regeneration. Generation of a damage model based on reflection, geometry measurement and thermographyCLEO 2013, 16.5.2013 München
  • Tesch, M.; Aschenbruck, J.; Hohenstein, S.; Schmidt, A.; Seume, J. R. (2013) Technik entdecken - Schüler-Lehrer-Tag an der Universität HannoverInquiry-based Learning - Forschendes Lernen Jahrestagung in Hannover 2012. Kiel: IPN (Gesellschaft für Didaktik der Chemie und Physik, 33), S. 659–661
  • Denkena, B.; Flöter, F. (2012) Dexterous Regeneration Cell for the Repair of Aircraft Engine ComponentsNeue Fertigungstechnologien der Luft- und Raumfahrt. Universität Hannover, I. F.W. Hannover, 01.01.2012
  • Rogge, T.; Rolfes, R. (2012) Stochastische Untersuchungen regenerationsbedingter Imperfektionen einer Turbinenschaufel: Modellierung des deterministischen Modells zur effizienten Berechnung des Schwingungs- und Festigkeitsverhaltens5. Dresdner-Probabilistik-Workshop. Dresden, S. 1–11
  • Aschenbruck, J.; Weidlich, N.; Herde, F.; Seume, J. R. (2011) Nachhaltige Regeneration von FlugzeugtriebwerkenDLRK 2011 in der Session Innovation aus Niedersachsen Leichtbau und Triebwerktechnik. German Society for Aeronautics and Astronautics. Bremen, 01.01.2011
  • Nicolaus, M.; Möhwald, K.; Bach, F.-W. (2011) Reparaturlöten von Turbinenschaufeln mittels thermischen SpritzensTagungsband zum 14. Werkstofftechnisches Kolloquium & 9. Industriefachtagung Oberflächen- und Wärmebehandlungstechnik. Chemnitz: Eigenverlag, S. 231–236
  • Ohrt, C.; Krauss, M.; Kästner, M.; Reithmeier, E. (2011) Optimierung eines endoskopischen StreifenprojektionssystemsSpani Molella, Luca Spani (Hg.): Vierter Workshop Optische Technologien. Tagungsband ; 17 - 18 November 2010. Garbsen: PZH, Produktionstechn. Zentrum
  • Nicolaus, M.; Möhwald, K.; Bach, F.-W. (2010) Neue Lösungswege für das Reparaturlöten und -beschichten von TurbinenschaufelnNeue Fertigungstechnologien in der Luft- und Raumfahrt, Machining Innovations Conference; Tagungsband, 23. und 24. November 2010, Hannover, S. 435–447; Garbsen: PZH, Produktionstechn. Zentrum (Berichte aus dem IFW, 2010,8),

Bücher, Monographien

  • Hennecke, C. J. W. (2018) Methodik einer Zustandsbeurteilung von TriebwerksbrennkammernGarbsen: TEWISS (Berichte aus dem ITV)
  • Herde, F. (2013) Rahmenbedingungen der industriellen Regeneration von zivilen Flugzeugtriebwerken2013. Norderstedt: BoD-Verlag

Dissertationen

  • Kuprat T. (2018) Modellgestütztes Ersatzteilmanagement in der Regeneration komplexer InvstitionsgüterGarbsen: TEWISS Verlag
  • Bruchwald, O. (2017) In-situ-Erfassung der Werkstoffumwandlung und Gefügeausbildung mittels WirbelstromtechnikBerichte aus dem IW 02/2017, PZH Verlag, Garbsen 2017
    ISBN: 3959001347
  • Flöter, F. B. (2017) Potentiale einer elektromagnetischen Führung in Fräsmaschinen und ihr Nutzen für die ReparaturbearbeitungBerichte aus dem IFW, Band 03/2017, 145 S., PZH Produktionstechnisches Zentrum
    ISBN: 978-3-95900-126-7
  • Li, Y. (2017) Multiscale and multimodal geometric measurement and data fusion technologies for robot guided surface metrologyBerichte aus dem IMR, PZH Verlag, Garbsen 2017
    ISBN: 3959001487
  • Pohle, L. (2017) Schwingungsverhalten verstimmter zyklischer Systeme und deren Optimierung durch bewusste VerstimmungBerichte aus dem IDS, Band 02/2017, PZH Verlag
    ISBN: 978-3-95900-132-8
  • Hohl, A. (2015) Modellierung zyklischer Strukturen mit Unsicherheiten und theoretische Betrachtung der Energielokalisierung in verstimmten SchaufelkränzenBerichte aus dem IDS, Band 01/2015, PZH Verlag
    ISBN: 978-3-95900-009-3
  • Nespor, D. (2015) Randzonenbeeinflussung durch die Rekonturierung komplexer Investitionsgüter aus Ti-6Al-4VBerichte aus dem IFW, Band 07/2015, 111 S., PZH Produktionstechnisches Zentrum
    ISBN: 978-3-95900-056-7
  • Adamczuk, R. (2014) Zustandsbeurteilung eines Triebwerks durch die Analyse des AbgasstrahlsLeibniz Universität Hannover, Berichte aus Institut für Turbomaschinen und Fluid-Dynamik Band 6/2014
  • Eickemeyer, S.C. (2014) Kapazitätsplanung und -abstimmung für die Regeneration komplexer InvestitionsgüterLeibniz Universität Hannover, Garbsen: Berichte aus dem IFA
    ISBN: 978-3-944586-77-9
  • Hackelöer, F. (2014) Erweiterungen der Einsatzmöglichkeiten von MagnetführungenBerichte aus dem IFW, Band 05/2014, PZH, Garbsen, 2014
    ISBN: 978-3-944586-71-7
  • Hohenstein, S. (2014) Einfluss komplexer Oberflächenstrukturen auf das aerodynamische Verlustverhalten von TurbinenbeschaufelungenLeibniz Universität Hannover, Berichte aus Turbomaschinen und Fluid-Dynamik, Band 4/2014
  • Holl, M. (2014) Multiscale crack propagation and crack coalescence using the XFEMDissertation B14/1, Institut für Kontinuumsmechanik
  • Kellenbrink, C. (2014) Ressourcenbeschränkte Projektplanung für flexible Projekte2014. Wiesbaden: Springer Fachmedien Wiesbaden
    ISBN: 978-3-65802-870-1
  • Pösch, A. (2014) Fast detection and analysis of geometry defects on free form surfaces using model-based inverse fringe projection2014. Garbsen: TEWISS - Technik und Wissen GmbH (Berichte aus dem imr, 04/2014)
    ISBN: 978-3-94458-691-5
  • Berkholz, D. A. (2012) Grundmodell zur Kapazitäts- und Belastungsabstimmung eines Arbeitssystems in der RegenerationBerichte aus dem IFA, Garbsen 2012
    ISBN: 978-3-943104-60-8